AC4LESS Dispatch Active

(626) 409-2552

Refrigerant specialists · Baldwin Park & the San Gabriel Valley

R-410A (Puron) AC Repair, Leak Detection & Recharge in Baldwin Park

Most air conditioners and heat pumps installed between about 2010 and 2025 run on R-410A, often sold as Puron. It replaced R-22 because it doesn't harm the ozone layer, and it runs at much higher pressure, so it needs tools and techniques rated for it. Your R-410A system can still be serviced and recharged — here's what to know.

What the 2025–2026 refrigerant rules mean for you

  • Existing R-410A systems can still be serviced, repaired and recharged
  • New residential R-410A split systems stopped being manufactured on January 1, 2025
  • A May 2026 EPA rule removed the 2026 installation deadline for R-410A equipment made before 2025
  • New systems use lower-GWP refrigerants such as R-454B and R-32, and HFC supply is being phased down

Why R-410A service is different

  • Roughly 60% higher operating pressure than R-22 — gauges, hoses and parts must be rated for it
  • POE oil absorbs moisture quickly, so the system has to stay sealed and be evacuated thoroughly
  • It's a blend, so it's charged as a liquid to keep the mix correct
  • Low charge means a leak — topping off without a repair just wastes refrigerant

How we service an R-410A system

  1. 1

    Measure before we touch it

    We check pressures, superheat and subcooling, airflow and electrical readings to confirm the problem really is refrigerant.

  2. 2

    Find the leak

    Electronic leak detection, bubble testing and nitrogen pressure testing pinpoint the leak — coils, flare fittings and service valves are common spots.

  3. 3

    Repair and pressure-test

    We repair the leak and pressure-test with dry nitrogen to prove the system holds.

  4. 4

    Deep vacuum

    Because POE oil holds moisture, we evacuate to a deep vacuum and confirm it holds before charging.

  5. 5

    Liquid charge to specification

    R-410A is weighed in or charged as a liquid to the manufacturer's specification, then fine-tuned with superheat or subcooling.

  6. 6

    Verify performance

    We confirm the temperature split, pressures and amperage, and explain the results and options in plain English.

R-410A vs. R-22 at a glance

R-22 vs. R-410A refrigerant specifications
PropertyR-22R-410A
Chemical designationHCFC-22 (chlorodifluoromethane)HFC-410A: 50% R-32 / 50% R-125 blend
Common namesFreon, R-22Puron and other brand names
ASHRAE safety classA1 (non-flammable)A1 (non-flammable)
Ozone depletion potential0.0550
Global warming potential (AR4, 100-yr)1,8102,088
Boiling point at sea level−40.8 °C (−41.4 °F)about −51 °C (−60 °F)
Saturated pressure at 70 °Fabout 121 psigabout 200 psig
Compressor oilMineral oil or alkylbenzenePOE (polyolester), absorbs moisture
How it's chargedAs vapor or liquidAs liquid (it's a blend)
Typical systemsInstalled before about 2010Installed about 2010–2025
U.S. statusNo new production or import since Jan 1, 2020No new residential split systems built since Jan 1, 2025; still serviceable

Pressures are approximate saturated values and vary with temperature. Always follow the equipment manufacturer's charging specifications.

Have an older system? See our R-22 (Freon) refrigerant service page.

Repair, or move to a new system?

Most R-410A systems are young enough that repairing a leak is the right call. If the system is past about 12–15 years, needs a compressor, or keeps leaking from the coil, a new high-efficiency system on R-454B or R-32 may cost less over time — and it can't be done by simply swapping refrigerants in your current equipment.

See AC installation and replacement, heat pump systems, or estimate sizing with our BTU & SEER2 calculator.

R-410A refrigerant FAQs

Is R-410A being phased out? Can my system still be repaired?

New residential R-410A split systems stopped being manufactured on January 1, 2025, and new equipment uses lower-GWP refrigerants such as R-454B and R-32. Existing R-410A systems can still be serviced, repaired and recharged, and a May 2026 EPA rule removed the 2026 installation deadline for R-410A equipment made before 2025.

What is the difference between R-410A and R-22?

R-410A is a chlorine-free blend of R-32 and R-125 with zero ozone depletion potential. It runs at roughly 60% higher pressure than R-22 and uses POE oil, so the two refrigerants and their equipment are not interchangeable.

Can my R-410A system be converted to R-454B or R-32?

Generally no. R-454B and R-32 are mildly flammable (A2L) refrigerants, and equipment has to be designed and listed for them. When an R-410A system reaches the end of its life, the usual path is a new system built for the newer refrigerant.

Why is R-410A charged as a liquid?

R-410A is a blend of two refrigerants. Charging it as a liquid keeps the blend's composition correct; charging it as vapor from the cylinder can change the mix and hurt performance.

Can you just top off my R-410A system?

A system that's low on refrigerant has a leak. Adding refrigerant without finding the leak means paying for the same refrigerant again later, so we locate and repair the leak, pull a deep vacuum, and then charge to the manufacturer's specification.

Do you sell R-410A refrigerant?

No. AC4LESS provides refrigerant service — leak repair, recovery and recharge by our technicians. We don't sell refrigerant to the public.